Accessories
Gas Control Unit
Consist of Gas Regulator with pressure gauge for regulating gas flow to wire Flame Spray Gun. It has two pressure gauge to indicate cylinder and delivery pressure.
| Oxygen | 10 Bar | |
| Pressure Rating | LPG/Propane | 06 Bar |
| Acetylene | 2.5 Bar |
Air Control Unit
Consist of air filter cum regulator for secondary filtration and regulating air flow to wire flame spray gun. An additional outlet provides connections for operator’s helmet.
Pressure Rating: 10 Bar
Hose Kit
Consist of Hose to connect oxygen cylinder & fuel gas cylinder with gas flow meter to spray gun.
| Oxygen Hose | Blue | 3+7 Mtrs. |
| Fuel Gas Hose | Red | 3+7 Mtrs. |
| Air Hose | Black | 7 Mtrs. |
Air Flow Meter with Hose
The 3AFM Air Flow Meter is a highly accurate, rugged and reliable instrument for regulating and measuring the flow of compressed air in a manual powder or wire combustion spray system.
Model: 3AFM (Air Flow Meter)
Flow Unit in both NLPM & SCFM
Gas Flow Meter
These precision wall mounting Flowmeters are recommended to use with Flame Spray Equipment. Ease of reading enables economic operation and rapid fault diagnosis. The unit incorporates separate flowmeter for both Oxygen and Fuel Gas supplies.
Model: 3GFM (Gas Flow Meter)
Flow Unit in both NLPM & SCFM
Model: 2GFM (Gas Flow Meter) Supply with % scale of 0 – 100
Model: 2GFM (Gas Flow Meter) Supply with % scale of 0 – 100
Wire Control Unit
The Wire Reel Stand with Straightner is specifically designed to dispense wires for flame spraying. A wire straightener is included and the unit is capable of handling either reeled or loose coiled wire or spool.
A Trolley with Reel Stand is also available to move the complete system in shop easily. Flow meters are shown only for representation purpose. They are not supplied with the trolley.
A Trolley with Reel Stand is also available to move the complete system in shop easily. Flow meters are shown only for representation purpose. They are not supplied with the trolley.
Extension Nozzles
Where deep bores or recesses are to be sprayed, a range of extension nozzles are available These allow access of the spray at depths, whilst straight or deflector air caps can be selected to direct the spray stream to the area required.
Typical use include spraying in internal diameter or hard to reach coating surfaces. For ID coatings, a minimum ID measurement of approximately 8 inches is required to achieve optimal coating quality.
Installation is simple by removing the standard Air Cap Body and Siphon plug and replacing it with the extension. This can be done in about 1-2 minutes without any tools. These are available in various lengths for both Oxy-Acetylene and Oxy-Propane Gun
Length: 6 INCH / 1 FOOT
SAFETY WEARS
Metallizing Helmet
Light weight & comfortable with excellent
vision. Supplied from a separate air supply
which should be filtered by Helmet Air
Conditioner.
Air Breather
This is installed in between
compressed air line originating
from fitting to the operators
helmets. Activated charcoal is
contained in the breather unit
which separates the oil traces from
the compressed air and clean
compressed air is fed to the
operator’s helmet.
Helmet Air Conditioner
Air from the air breather is fed to the helmet air conditioner and air is contained before it is fed to the helmet for breathing. It has also a regulator knob so that the operator can regulate the temperature of air fed to the helmet. It is self driven and doesn’t need external power.
Ear Muff
Light weight & comfort able.
Operator & other personnel close to
the spray operation must wear.
Protect the operator from noise
originating during thermal spray.
Protective Glass
Light weight & comfortable with excellent vision. Operator & other personnel close to the spray operation must wear.
Operator Safety Mask
Ensure clean breathing air at all times. Conforms to current legislation on breathing air quality.
Hand Gloves
These are made of rubber and have anti-static properties. Hand gloves protect the operators’ hand against flying abrasive and static charge if any.
Gas Control Unit
Consist of Gas Regulator with pressure gauge for regulating gas flow to wire Flame Spray Gun. It has two pressure gauge to indicate cylinder and delivery pressure.
| Oxygen | 10 Bar | |
| Pressure Rating | LPG/Propane | 06 Bar |
| Acetylene | 2.5 Bar |
Air Control Unit
Consist of air filter cum regulator for secondary filtration and regulating air flow to wire flame spray gun. An additional outlet provides connections for operator’s helmet.
Pressure Rating: 10 Bar
Hose Kit
Consist of Hose to connect oxygen cylinder & fuel gas cylinder with gas flow meter to spray gun.
| Oxygen Hose | Blue | 3+7 Mtrs. |
| Fuel Gas Hose | Red | 3+7 Mtrs. |
| Air Hose | Black | 7 Mtrs. |
Air Flow Meter with Hose
The 3AFM Air Flow Meter is a highly accurate, rugged and reliable instrument for regulating and measuring the flow of compressed air in a manual powder or wire combustion spray system.
Model: 3AFM (Air Flow Meter)
Flow Unit in both NLPM & SCFM
Air Flow Meter with Hose
The 3AFM Air Flow Meter is a highly accurate, rugged and reliable instrument for regulating and measuring the flow of compressed air in a manual powder or wire combustion spray system.
Model: 3GFM (Gas Flow Meter)
Flow Unit in both NLPM & SCFM
Model: 2GFM (Gas Flow Meter) Supply with % scale of 0 – 100
Model: 2GFM (Gas Flow Meter) Supply with % scale of 0 – 100
Wire Control Unit
The Wire Reel Stand with Straightner is specifically designed to dispense wires for flame spraying. A wire straightener is included and the unit is capable of handling either reeled or loose coiled wire or spool.
A Trolley with Reel Stand is also available to move the complete system in shop easily. Flow meters are shown only for representation purpose. They are not supplied with the trolley.
A Trolley with Reel Stand is also available to move the complete system in shop easily. Flow meters are shown only for representation purpose. They are not supplied with the trolley.
SAFETY WEARS
Metallizing Helmet
Light weight & comfortable with excellent
vision. Supplied from a separate air supply
which should be filtered by Helmet Air
Conditioner.
Air Breather
This is installed in between
compressed air line originating
from fitting to the operators
helmets. Activated charcoal is
contained in the breather unit
which separates the oil traces from
the compressed air and clean
compressed air is fed to the
operator’s helmet.
Helmet Air Conditioner
Air from the air breather is fed to the helmet air conditioner and air is contained before it is fed to the helmet for breathing. It has also a regulator knob so that the operator can regulate the temperature of air fed to the helmet. It is self driven and doesn’t need external power.
Ear Muff
Light weight & comfort able.
Operator & other personnel close to
the spray operation must wear.
Protect the operator from noise
originating during thermal spray.
Protective Glass
Light weight & comfortable with excellent vision. Operator & other personnel close to the spray operation must wear.
Operator Safety Mask
Ensure clean breathing air at all times. Conforms to current legislation on breathing air quality.
Hand Gloves
These are made of rubber and have anti-static properties. Hand gloves protect the operators’ hand against flying abrasive and static charge if any.
Gas Control Unit
Consist of Gas Regulator with pressure gauge for regulating gas flow to wire Flame Spray Gun. It has two pressure gauge to indicate cylinder and delivery pressure.
Air Control Unit
Consist of air filter cum regulator for secondary filtration and regulating air flow to wire flame spray gun. An additional outlet provides connections for operator’s helmet.
Pressure Rating: 10 Bar
Hose Kit
Consist of Hose to connect oxygen cylinder & fuel gas cylinder with gas flow meter to spray gun.
Air Flow Meter with Hose
The 3AFM Air Flow Meter is a highly accurate, rugged and reliable instrument for regulating and measuring the flow of compressed air in a manual powder or wire combustion spray system.
Model: 3AFM (Air Flow Meter)
Flow Unit in both NLPM & SCFM
Gas Flow Meter
These precision wall mounting Flowmeters are recommended to use with Flame Spray Equipment. Ease of reading enables economic operation and rapid fault diagnosis. The unit incorporates separate flowmeter for both Oxygen and Fuel Gas supplies.
Model: 3GFM (Gas Flow Meter)
Flow Unit in both NLPM & SCFM
Model: 2GFM (Gas Flow Meter) Supply with % scale of 0 – 100
Model: 2GFM (Gas Flow Meter) Supply with % scale of 0 – 100
Wire Control Unit
The Wire Reel Stand with Straightner is specifically designed to dispense wires for flame spraying. A wire straightener is included and the unit is capable of handling either reeled or loose coiled wire or spool.
A Trolley with Reel Stand is also available to move the complete system in shop easily. Flow meters are shown only for representation purpose. They are not supplied with the trolley.
A Trolley with Reel Stand is also available to move the complete system in shop easily. Flow meters are shown only for representation purpose. They are not supplied with the trolley.
Extension Nozzles
Where deep bores or recesses are to be sprayed, a range of extension nozzles are available These allow access of the spray at depths upto 1.1 Mtr., whilst straight or deflector air caps can be selected to direct the spray stream to the area required.
Typical use include spraying in internal diameter or hard to reach coating surfaces. For ID coatings, a minimum ID measurement of approximately 8 inches is required to achieve optimal coating quality.
Installation is simple by removing the standard Air Cap Body and Siphon plug and replacing it with the extension. This can be done in about 1-2 minutes without any tools. These are available in various lengths for both Oxy-Acetylene and Oxy-Propane Gun
Typical use include spraying in internal diameter or hard to reach coating surfaces. For ID coatings, a minimum ID measurement of approximately 8 inches is required to achieve optimal coating quality.
Installation is simple by removing the standard Air Cap Body and Siphon plug and replacing it with the extension. This can be done in about 1-2 minutes without any tools. These are available in various lengths for both Oxy-Acetylene and Oxy-Propane Gun
Length: 6 INCH / 1 FOOT / 2 FEET / 3 FEET
SAFETY WEARS
Metallizing Helmet
Light weight & comfortable with excellent
vision. Supplied from a separate air supply
which should be filtered by Helmet Air
Conditioner.
Air Breather
This is installed in between
compressed air line originating
from fitting to the operators
helmets. Activated charcoal is
contained in the breather unit
which separates the oil traces from
the compressed air and clean
compressed air is fed to the
operator’s helmet.
Helmet Air Conditioner
Air from the air breather is fed to the helmet air conditioner and air is contained before it is fed to the helmet for breathing. It has also a regulator knob so that the operator can regulate the temperature of air fed to the helmet. It is self driven and doesn’t need external power.
Ear Muff
Light weight & comfort able.
Operator & other personnel close to
the spray operation must wear.
Protect the operator from noise
originating during thermal spray.
Protective Glass
Light weight & comfortable with excellent vision. Operator & other personnel close to the spray operation must wear.
Operator Safety Mask
Ensure clean breathing air at all times. Conforms to current legislation on breathing air quality.
Hand Gloves
These are made of rubber and have anti-static properties. Hand gloves protect the operators’ hand against flying abrasive and static charge if any.
Gas Control Unit
Consist of Gas Regulator with pressure gauge for regulating gas flow to wire Flame Spray Gun. It has two pressure gauge to indicate cylinder and delivery pressure.
Air Control Unit
Consist of air filter cum regulator for secondary filtration and regulating air flow to wire flame spray gun. An additional outlet provides connections for operator’s helmet.
Pressure Rating: 10 Bar
Hose Kit
Consist of Hose to connect oxygen cylinder & fuel gas cylinder with gas flow meter to spray gun.
Air Flow Meter with Hose
The 3AFM Air Flow Meter is a highly accurate, rugged and reliable instrument for regulating and measuring the flow of compressed air in a manual powder or wire combustion spray system.
Model: 3AFM (Air Flow Meter)
Flow Unit in both NLPM & SCFM
Gas Flow Meter
These precision wall mounting Flowmeters are recommended to use with Flame Spray Equipment. Ease of reading enables economic operation and rapid fault diagnosis. The unit incorporates separate flowmeter for both Oxygen and Fuel Gas supplies.
Model: 3GFM (Gas Flow Meter)
Flow Unit in both NLPM & SCFM
Model: 2GFM (Gas Flow Meter) Supply with % scale of 0 – 100
Model: 2GFM (Gas Flow Meter) Supply with % scale of 0 – 100
Wire Control Unit
The Wire Reel Stand with Straightner is specifically designed to dispense wires for flame spraying. A wire straightener is included and the unit is capable of handling either reeled or loose coiled wire or spool.
A Trolley with Reel Stand is also available to move the complete system in shop easily. Flow meters are shown only for representation purpose. They are not supplied with the trolley.
Extension Nozzles
Where deep bores or recesses are to be sprayed, a range of extension nozzles are available These allow access of the spray at depths upto 1.1 Mtr., whilst straight or deflector air caps can be selected to direct the spray stream to the area required.
Typical use include spraying in internal diameter or hard to reach coating surfaces. For ID coatings, a minimum ID measurement of approximately 8 inches is required to achieve optimal coating quality.
Installation is simple by removing the standard Air Cap Body and Siphon plug and replacing it with the extension. This can be done in about 1-2 minutes without any tools. These are available in various lengths for both Oxy-Acetylene and Oxy-Propane Gun
Typical use include spraying in internal diameter or hard to reach coating surfaces. For ID coatings, a minimum ID measurement of approximately 8 inches is required to achieve optimal coating quality.
Installation is simple by removing the standard Air Cap Body and Siphon plug and replacing it with the extension. This can be done in about 1-2 minutes without any tools. These are available in various lengths for both Oxy-Acetylene and Oxy-Propane Gun
Length: 1 FOOT / 2 FEET / 3 FEET
SAFETY WEARS
Metallizing Helmet
Light weight & comfortable with excellent
vision. Supplied from a separate air supply
which should be filtered by Helmet Air
Conditioner.
Air Breather
This is installed in between
compressed air line originating
from fitting to the operators
helmets. Activated charcoal is
contained in the breather unit
which separates the oil traces from
the compressed air and clean
compressed air is fed to the
operator’s helmet.
Helmet Air Conditioner
Air from the air breather is fed to the helmet air conditioner and air is contained before it is fed to the helmet for breathing. It has also a regulator knob so that the operator can regulate the temperature of air fed to the helmet. It is self driven and doesn’t need external power.
Ear Muff
Light weight & comfort able.
Operator & other personnel close to
the spray operation must wear.
Protect the operator from noise
originating during thermal spray.
Protective Glass
Light weight & comfortable with excellent vision. Operator & other personnel close to the spray operation must wear.
Operator Safety Mask
Ensure clean breathing air at all times. Conforms to current legislation on breathing air quality.
Hand Gloves
These are made of rubber and have anti-static properties. Hand gloves protect the operators’ hand against flying abrasive and static charge if any.
Gas Control Unit
Consist of Gas Regulator with pressure gauge for regulating gas flow to wire Flame Spray Gun. It has two pressure gauge to indicate cylinder and delivery pressure.
| Oxygen | 10 Bar | |
| Pressure Rating | LPG/Propane | 06 Bar |
| Acetylene | 2.5 Bar |
Air Control Unit
Consist of air filter cum regulator for secondary filtration and regulating air flow to wire flame spray gun. An additional outlet provides connections for operator’s helmet.
Pressure Rating: 10 Bar
Hose Kit
Consist of Hose to connect oxygen cylinder & fuel gas cylinder with gas flow meter to spray gun.
| Oxygen Hose | Blue | 3+7 Mtrs. |
| Fuel Gas Hose | Red | 3+7 Mtrs. |
| Air Hose | Black | 7 Mtrs. |
Air Flow Meter with Hose
The 3AFM Air Flow Meter is a highly accurate, rugged and reliable instrument for regulating and measuring the flow of compressed air in a manual powder or wire combustion spray system.
Model: 3AFM (Air Flow Meter)
Flow Unit in both NLPM & SCFM
Gas Flow Meter
These precision wall mounting Flowmeters are recommended to use with Flame Spray Equipment. Ease of reading enables economic operation and rapid fault diagnosis. The unit incorporates separate flowmeter for both Oxygen and Fuel Gas supplies.
Model: 3GFM (Gas Flow Meter)
Flow Unit in both NLPM & SCFM
Model: 2GFM (Gas Flow Meter) Supply with % scale of 0 – 100
Model: 2GFM (Gas Flow Meter) Supply with % scale of 0 – 100
Wire Control Unit
The Wire Reel Stand with Straightner is specifically designed to dispense wires for flame spraying. A wire straightener is included and the unit is capable of handling either reeled or loose coiled wire or spool.
A Trolley with Reel Stand is also available to move the complete system in shop easily. Flow meters are shown only for representation purpose. They are not supplied with the trolley.
A Trolley with Reel Stand is also available to move the complete system in shop easily. Flow meters are shown only for representation purpose. They are not supplied with the trolley.
Extension Nozzles
Where deep bores or recesses are to be sprayed, a range of extension nozzles are available These allow access of the spray at depths upto 1.1 Mtr., whilst straight or deflector air caps can be selected to direct the spray stream to the area required.
Typical use include spraying in internal diameter or hard to reach coating surfaces. For ID coatings, a minimum ID measurement of approximately 8 inches is required to achieve optimal coating quality.
Installation is simple by removing the standard Air Cap Body and Siphon plug and replacing it with the extension. This can be done in about 1-2 minutes without any tools. These are available in various lengths for both Oxy-Acetylene and Oxy-Propane Gun
Typical use include spraying in internal diameter or hard to reach coating surfaces. For ID coatings, a minimum ID measurement of approximately 8 inches is required to achieve optimal coating quality.
Installation is simple by removing the standard Air Cap Body and Siphon plug and replacing it with the extension. This can be done in about 1-2 minutes without any tools. These are available in various lengths for both Oxy-Acetylene and Oxy-Propane Gun
Length: 6 INCH / 1 FOOT / 2 FEET / 3 FEET
SAFETY WEARS
Metallizing Helmet
Light weight & comfortable with excellent
vision. Supplied from a separate air supply
which should be filtered by Helmet Air
Conditioner.
Air Breather
This is installed in between
compressed air line originating
from fitting to the operators
helmets. Activated charcoal is
contained in the breather unit
which separates the oil traces from
the compressed air and clean
compressed air is fed to the
operator’s helmet.
Helmet Air Conditioner
Air from the air breather is fed to the helmet air conditioner and air is contained before it is fed to the helmet for breathing. It has also a regulator knob so that the operator can regulate the temperature of air fed to the helmet. It is self driven and doesn’t need external power.
Ear Muff
Light weight & comfort able.
Operator & other personnel close to
the spray operation must wear.
Protect the operator from noise
originating during thermal spray.
Protective Glass
Light weight & comfortable with excellent vision. Operator & other personnel close to the spray operation must wear.
Operator Safety Mask
Ensure clean breathing air at all times. Conforms to current legislation on breathing air quality.
Hand Gloves
These are made of rubber and have anti-static properties. Hand gloves protect the operators’ hand against flying abrasive and static charge if any.
Gas Control Unit
Consist of Gas Regulator with pressure gauge for regulating gas flow to wire Flame Spray Gun. It has two pressure gauge to indicate cylinder and delivery pressure.
| Oxygen | 10 Bar | |
| Pressure Rating | LPG/Propane | 06 Bar |
| Acetylene | 2.5 Bar |
Air Control Unit
Consist of air filter cum regulator for secondary filtration and regulating air flow to wire flame spray gun. An additional outlet provides connections for operator’s helmet.
Pressure Rating: 10 Bar
Hose Kit
Consist of Hose to connect oxygen cylinder & fuel gas cylinder with gas flow meter to spray gun.
| Oxygen Hose | Blue | 3+7 Mtrs. |
| Fuel Gas Hose | Red | 3+7 Mtrs. |
| Air Hose | Black | 7 Mtrs. |
Air Flow Meter with Hose
The 3AFM Air Flow Meter is a highly accurate, rugged and reliable instrument for regulating and measuring the flow of compressed air in a manual powder or wire combustion spray system.
Model: 3AFM (Air Flow Meter)
Flow Unit in both NLPM & SCFM
Gas Flow Meter
These precision wall mounting Flowmeters are recommended to use with Flame Spray Equipment. Ease of reading enables economic operation and rapid fault diagnosis. The unit incorporates separate flowmeter for both Oxygen and Fuel Gas supplies.
Model: 3GFM (Gas Flow Meter)
Flow Unit in both NLPM & SCFM
Model: 2GFM (Gas Flow Meter) Supply with % scale of 0 – 100
Model: 2GFM (Gas Flow Meter) Supply with % scale of 0 – 100
Wire Control Unit
The Wire Reel Stand with Straightner is specifically designed to dispense wires for flame spraying. A wire straightener is included and the unit is capable of handling either reeled or loose coiled wire or spool.
A Trolley with Reel Stand is also available to move the complete system in shop easily. Flow meters are shown only for representation purpose. They are not supplied with the trolley.
A Trolley with Reel Stand is also available to move the complete system in shop easily. Flow meters are shown only for representation purpose. They are not supplied with the trolley.
Extension Nozzles
Where deep bores or recesses are to be sprayed, a range of extension nozzles are available These allow access of the spray at depths upto 1.1 Mtr., whilst straight or deflector air caps can be selected to direct the spray stream to the area required.
Typical use include spraying in internal diameter or hard to reach coating surfaces. For ID coatings, a minimum ID measurement of approximately 8 inches is required to achieve optimal coating quality.
Installation is simple by removing the standard Air Cap Body and Siphon plug and replacing it with the extension. This can be done in about 1-2 minutes without any tools. These are available in various lengths for both Oxy-Acetylene and Oxy-Propane Gun
Typical use include spraying in internal diameter or hard to reach coating surfaces. For ID coatings, a minimum ID measurement of approximately 8 inches is required to achieve optimal coating quality.
Installation is simple by removing the standard Air Cap Body and Siphon plug and replacing it with the extension. This can be done in about 1-2 minutes without any tools. These are available in various lengths for both Oxy-Acetylene and Oxy-Propane Gun
Length: 6 INCH / 1 FOOT / 2 FEET / 3 FEET
SAFETY WEARS
Metallizing Helmet
Light weight & comfortable with excellent
vision. Supplied from a separate air supply
which should be filtered by Helmet Air
Conditioner.
Air Breather
This is installed in between
compressed air line originating
from fitting to the operators
helmets. Activated charcoal is
contained in the breather unit
which separates the oil traces from
the compressed air and clean
compressed air is fed to the
operator’s helmet.
Helmet Air Conditioner
Air from the air breather is fed to the helmet air conditioner and air is contained before it is fed to the helmet for breathing. It has also a regulator knob so that the operator can regulate the temperature of air fed to the helmet. It is self driven and doesn’t need external power.
Ear Muff
Light weight & comfort able.
Operator & other personnel close to
the spray operation must wear.
Protect the operator from noise
originating during thermal spray.
Protective Glass
Light weight & comfortable with excellent vision. Operator & other personnel close to the spray operation must wear.
Operator Safety Mask
Ensure clean breathing air at all times. Conforms to current legislation on breathing air quality.
Hand Gloves
These are made of rubber and have anti-static properties. Hand gloves protect the operators’ hand against flying abrasive and static charge if any.
